“–Kurzschluss Booster–“

The Intellibox I from Uhlenbrock shows “–Kurzschluss Booster–“, What to do?

Before you hunt for short circuits on your layout, first disconnect the boosters and the Intellibox I from your layout and connect them to a very small system that only connects the boosters to the Intellibox I but nothing else. No trains, signals, rails, rolling stock or anything else. If this small subsystem still shows the error, you know that there is no short circuit caused by your layout or anything on it but the settings in either the boosters or the Intellibox are incorrect.

If the small subsystem still shows the error, try the solution outlined here. For me the solution option A did the trick. It tells you to set the Sonderoption (custom option) 25 to the Value 1 and the Sonderoption 907 to the Value 5.

The peculiar thing is the the error is described as the Intellibox I sending DCC commands to a Märklin Booster 6017 which will signal a short circuit back to the Intellibox because it cannot correctly process the DCC signals. My dad swears that he used the system in Motorla / DCC co-operation for two years and the problem never occured. I do not know what to think about all this, but Solution A solved it at least for now.

The following text is taken from the Uhlenbrock FAQ and is not mine! I did copy it in case the Uhlenbrock FAQ goes away. The Uhlenbrock FAQ is awesome and spot on and it would be a shame if it is lost one day.

Problem/Frage:
Wenn die Intellibox mit einem Märklin 6017 Booster betrieben wird, erscheint nach dem einschalten der Anlage die Fehlermeldung:
  "--Kurzschluss Booster--".
Hinweis:
Fall A - Sie benutzen nur Motorola-Decoder

es ist wahrscheinlich, dass Sie, obwohl Sie nur Motorola-Decoder benutzen, doch zumindest einmal eine DCC-Lok "zum ausprobieren" aufgerufen haben.

Dies hat zur Folge, dass die Intellibox automatisch die Sonderoption 25 auf den Wert 1 und die Sonderoption 907 auf dem Wert 5 gestellt hat. Das bedeutet, dass beim Anschalten der Anlage ab jetzt auch ein DCC-Signal mit ausgesendet wird, welches vom Booster 6017 als Kurzschluß interpretiert wird.
Lösung:
  Bitte Sonderoption 25 zurücksetzen auf Wert = 0
  Bitte Sonderoption 907 zurücksetzen auf Wert = 1

Falls trotzt dieser Änderung immer noch eine Kurzschluss- Fehlermeldung entsteht, verändern Sie bitte auch den Wert der Sonderoption 36 auf einen größeren Wert als die Werkseinstellung von 20 z.B. auf den Wert 100.
Hinweis:
Fall B - Sie fahren auch im Mischbetrieb mit DCC-Decodern.
Lösung:
die Sonderoption 901 ist wahrscheinlich nicht - laut Intellibox Handbuch - erhöht worden. Die Sonderoption 901 sollte auf den Wert 3 bis 5 gesetzt werden.

Falls trotzt dieser Änderung immer noch eine Kurzschluss- Fehlermeldung entsteht, verändern Sie bitte auch den Wert der Sonderoption 36 auf einen größeren Wert als die Werkseinstellung von 20 z.B. auf den Wert 100 .

Ebenso am Märklin Booster die DIP-Schalter 1 und 2 auf "on" stellen.

Kurzanleitung: Zurücksetzen einer Sonderoption auf die Werkseinstellung

Sonderoption anwählen, den Cursor auf die rechte Seite setzen und die "C" Taste so lange betätigen bis die Werkseinstellung der Sonderoption wieder im Display erscheint. Danach die [enter] Taste betätigen.

 

Leave a Reply